Thank you to our partners at MINDS-i for providing this resource. If you have questions about this information, please contact MINDS-i.
Here is your unified, step-by-step checklist covering everything from reading the documentation to flying, charging, and storing your Tattu 3S 1300mAh LiPo battery using the iMars Mini Smart Charger.
Phase 1: Pre-Check & Documentation
- Read the Manual: Review Gens Ace & Tattu's Safe Operations Guidelines before initial setup.
- Inspect the Battery Body: Check for swelling, dents, punctures, or tears in the outer wrap.
- Inspect the Wires: Verify that both the yellow XT60 connector and the white balance lead have no exposed copper.
- Set Up a Safe Charging Area: Place your fireproof LiPo safe bag on a heat-resistant surface (concrete, tile, or stone) away from carpet and curtains.
Phase 2: Charging Protocol (iMars Mini Manual Mode)
- Power On the Charger: Plug your iMars Mini into its 65W USB-C power source.
- Isolate the Pack: Place the Tattu battery completely inside your fireproof LiPo safe bag.
- Connect Main Power: Plug the yellow XT60 plug into the charger's matching port.
- Connect Balance Lead: Plug the white 3S balance plug into the charger's balance port.
- Verify LiPo Selection: Confirm that the charger's "LiPo" LED indicator light is active.
- Start Balance Charging: Press and hold the CHARGE button for 2–3 seconds until the status indicator turns solid green.
- Actively Monitor: Stay in the room for the duration of the charge. Never leave a active battery unattended.
- Disconnect Safely: Once the charger alerts you that it is finished, unplug the XT60 connector first, then the balance lead.
Phase 3: Discharging & Flight Safety
- Check Temperatures: Ensure the pack is at room temperature before plugging it into your drone.
- Set Voltage Alerts: Configure your drone's low-voltage alarm or telemetry cutoff to 3.3V per cell under load (9.9V total).
- Monitor Heat Post-Flight: Disconnect the pack immediately after landing. If it feels hotter than 140°F (60°C), let it cool down in a safe areaPhase 4: Storage Mode & Maintenance
- Determine Storage Need: If you are not planning to fly the battery again within the next 48 hours, proceed to storage mode.
- Connect to Charger: Reconnect both the XT60 and 3S balance plug to your iMars Mini.
- Activate Storage Charge: Press and hold the STORAGE button for 2 seconds to bring the cells to a safe nominal voltage (~3.8V–3.85V per cell).
- Final Storage Location: Place the battery back inside a fireproof container or safe bag, storing it at a steady room temperature (around 25°C). Do not stack packs tightly.
iMars Mini LED Warning Codes
If the charger detects a fault, it will stop charging and flash its indicator lights. Watch for these common error patterns:
- LiPo LED Flashing Rapidly: The charger cannot detect the battery cells properly. Double-check that your white balance plug is fully inserted.
- Red Error Light / Status Bar Flashing: This indicates a voltage error. Either a cell is severely over-discharged (below 3.0V) or a cell has failed entirely. Disconnect the battery immediately.
- All Lights Flashing Simultaneously: The charger is overheating or receiving unstable input power. Unplug the USB-C power source and let the unit cool down.
Checking Battery Health Without a Charger
To monitor your battery out in the field without plugging it into your iMars Mini, consider using a pocket-sized digital battery capacity checker:
- Cell Balancing: Connect the white balance lead to the checker to verify all 3 cells are within 0.02V of each other.
- Voltage Drift: If one cell stays consistently lower than the other two during use, the pack is degraded and should be retired.
Safe Disposal of Dead or Damaged LiPos
When your Tattu pack eventually puffs up, drops capacity significantly, or won't hold a balance, it must be permanently retired:
- Fully Discharge First: Use a specialized battery discharger, a halogen bulb setup, or your charger's deep discharge function to bring the total pack voltage down to 0.0V. A completely depleted lithium battery has no chemical energy left to catch fire.
- Insulate the Leads: Cut the battery leads one at a time (never cut both together, or your wire cutters will cause a violent short circuit). Wrap the exposed wire ends tightly in electrical tape.
- Do Not Trash: Do not throw the battery in household trash or standard recycling bins. Bring the insulated pack to a dedicated local e-waste collection site or a home improvement store (like Home Depot or Lowe's) that accepts rechargeable batteries.